Felkods manual till de flesta MB mellan 88-00

[Bjerven]

Hej
Skriver in en lista med felkoder till digitala klimatsystemet från 93-00.

A/C S ELF DIAGNOSTIC SYST EMS - 1990-97

210 Chassis from 9/95
READING ACTUAL VALUES
1. IGNITION : Position 1
2. Press the AUTO button
3. Set both temperature selectors to 72 degrees F.
4. Press the REST button for more than 5 seconds.
5. The left display will alternately show the number "1" and the in-car temperature.
6. Press the AUTO button and the next component number and its value will be displayed.
7. Press the REST button to end the test program.

COMPONENT UNDER T EST

Number Component

01 In-Car Temperature Sensor with Aspirator Blower (B10/4)

02 Outside Temperature Sensor (B14)

03 Left Heater Core Temperature Sensor (B10/1)

04 Right Heater Core Temperature Sensor (B10/1)

05 Evaporator Temperature Sensor (B10/6)

06 Engine Coolant Temperature (ECT) Sensor (A/C) (B1/4)

07 Refrigerant Pressure in Bar

08 Refrigerant Temperature Sensor (B12/1)

10 Blower Control Voltage

11 Emissions (Refrigerant Leak) Sensor (B31)

12 Sun (Excessive Heat) Sensor (B32)

20 Control Current for Auxiliary f-n exp. : 7 = 7 mA

21 Engine RPM. example 00..99 (x100) = 9900

22 Vehicle Speed

23 PIN 58D exp. 99.0 = 99% of Battery Voltage

24 Battery Voltage : 12.8 = 12,8 Volt

40 Software Version Encoded

41 Hardware Version

Fortsätter med nästa sida ->

[Bjerven]

A/C S ELF DIAGNOSTIC SYST EMS - 1990-97

210 Chassis from 9/95
FAULT DIAGNOSIS
1. IGNITION : Position 1
2. Left Temperature selector wheel : HI
Right Temperature selector wheel : LO
3. Within 20 seconds press the REST and EC buttons simultaneously for more than 5 seconds.
4. The LED in the RECIRCULATE button flashes and "dI R" appears on the display
5. Press the right AUTO button until all DTC's are displayed and recorded.
6. To erase, all codes must be read out. Press both AUTO buttons simultaneously for more than 2 seconds. "d" will be displayed
on the left and "FF" is displayed on the right. The erase can be canceled by pressing the AUTO.
7. Reset temperature selector to normal setting.
8. IGNITION : OFF to end the test program.

FAULT CODES - 210 Chassis from 9/95

DTC Readout Description

026 CAN - Communication

226 In-Car Air Temperature Sensor (B10/4)

227 Outside Air Temperature Sensor (B14)

228 Left Heater Core Temperature Sensor (B10/1)

229 Right Heater Core Temperature Sensor (B 10/1)

230 Evaporator Temperature Sensor (B10/6)

231 Engine Coolant Temperature Sensor (B10/8)

232 Refrigerant Pressure Sensor (B12)

233 Refrigerant Temperature Sensor (B12/1)

234 Sun Sensor (B32)

235 Emissions (Refrigerant Leak) Sensor (B31)

241 Refrigerant Level

416 Coolant Circulation Pump (M13)

417 Left Duovalve (Water Valve) (Y21y1)

418 Right Duovalve (Water Valve) (Y21y2)

419 A/C Compressor Electromagnetic Clutch (A9k1)

420 Closed (Idle) Throttle Speed Increase

421 Pulse Module

422 Serial Interface Connection (K 1) to Instrument Cluster (IC)

423 Switchover Valve Block (Y11)

424 Activated Charcoal Filter Actuator (A32m2) : OPEN

425 Activated Charcoal Filter Actuator (A32m2) : CLOSE

432 Maximum Heat

459 Serial Interface Connection (K2) to Instrument Cluster (IC)

462 Wide Open Throttle (WOT) Position Signal - Diesel Engine Only

[Bjerven]

Om det är någon som vill ha hela PDF filen på alla felkoder till MB 88-00,så kan ni skicka mig ett pm och jag skall försöka skicka den till er..
Är endast 544Kb stor.